Setup guide: Active/Passive Redundancy using Xen, DRBD and Heartbeat

classic Classic list List threaded Threaded
1 message Options
Reply | Threaded
Open this post in threaded view
|

Setup guide: Active/Passive Redundancy using Xen, DRBD and Heartbeat

Tom Hibbert
Hello again Xenophiles,

I've noticed a few people on the list having problems with Xen and DRBD,
so I thought I'd post an approximate walkthrough of the steps I've been
taking to bring it up. This guide is heavily Sarge oriented, and may or
may not be any use to anyone. The main reason for me documenting it is
actually so I dont forget again the next time I do it.

This guide assumes you already have two Xen Dom0 machines running. You
may or may not have a dedicated network interface for Heartbeat/DRBD, it
is not required.

1. Build and install the drbd
# apt-get install drbd0.7-module-source module-assistant

the module-assistant is a very handy tool that works well both with
vanilla and with debianised kernel sources. Using it eliminates the
requirement to repatch the kernel sources and rebuild.
 
# ARCH=xen module-assistant
--kernel-dir=/usr/src/kernels/kernel-source-2.6.10 build drbd0.7-module

Obviously replace the --kernel-dir directive with the path to your xen0
kernel.
Once module assistant has completed its machinations, install the
resultant deb on both machines:

# dpkg -i /usr/src/drbd0.7-module-*
# update-modules

... and just to be sure it's worked:

# modprobe drbd

Note that drbd can only be configured as a module (for reasons
unfathomable to me).

Finally install the drbd admin utilities:

# apt-get install drbd0.7-utils

2. Configure the drbd

First, make sure both nodes have entries in hosts file that match the
output from hostname. You must be able to resolve the remote node by its
hostname.

Edit the drbd.conf and add resource stanzas for all block devices you
need to replicate.

# nano /etc/drbd.conf

resource "r1" {
  protocol C;
  startup {
    wfc-timeout         60;
    degr-wfc-timeout  60;
  }
  disk {
    on-io-error detach;
  }
  net {
    # i have left these in incase i need to use them later
    # timeout           60;
    # connect-int       10;
    # ping-int          10;
    # max-buffers     2048;
    # max-epoch-size  2048;
  }
  syncer {
    rate   100M;
    group   1; # sync concurrently with r0
  }

  on uplink-xen-1 {
    device      /dev/drbd1;
    disk        /dev/md1;
    address     172.10.10.1:7789;
    meta-disk   internal;
  }

  on uplink-xen-2 {
    device     /dev/drbd1;
    disk       /dev/md1;
    address    172.10.10.2:7789;
    meta-disk  internal;
  }
}

Just so we're clear, the device declaration is the drbd device and the
disk declaration is the backend block device that will store the
replicated data. "meta-disk internal" means that drbd uses a part of the
device near the end to store its metadata, you can use an external
device or file here but internal reduces complexity somewhat.
NOTE when configuring replication using an existing filesystem, ie one
that wont be freshly created after drbd is brought up, you will probably
need to run e2resize on it to prevent "attempt to access beyond end of
device" errors.

Copy the drbd.conf file to both nodes and start drbd. Make sure the
referenced disks are not mounted before drbd is started, or Bad Things
Will Happen(tm).

# /etc/init.d/drbd start

drbd will come up on both nodes in "secondary" mode.

Make your "primary" node the primary for all drbd devices:

# drbdsetup /dev/drbdX primary --do-what-I-say

You can check the drbd status with:

# cat /proc/drbd

You may wish to wait for replication to complete before moving on to the
next step.


3. Installing heartbeat

# apt-get install heartbeat

# nano /etc/heartbeat/ha.cf

deadtime 60
warntime 30
initdead 120
bcast eth0
auto_failback off
node host1
node host2
logfacility local0

# nano /etc/heartbeat/haresources
host1     drbddisk::r2 drbddisk::r2 xendomains::domU

I created a simple "xendomains" script for (re)starting xen domains from
heartbeat.

/etc/ha.d/resource.d/xendomains

#!/bin/bash
XM="/usr/sbin/xm"
CONFPATH="/etc/xen/"
ems-fs-dom0
RES="$1"
CMD="$2"
isrunning=false

case "$CMD" in
    start)
        $XM create -f $CONFPATH$RES
        ;;
    stop)
        exec $XM destroy $RES
        ;;
    status)
        $XM list | awk '{print $1}'  | grep $RES > /dev/null
        if [ $? -eq 0 ]
        then
                echo running
        else
                echo stopped
        fi
        ;;
    *)
        echo "Usage: xendomain [filename] {start|stop|status}"
        exit 1
        ;;
esac

exit 0


There are a few more files that need to be edited

# nano /etc/ha.d/authkeys

auth 1
1 crc

# chmod 600 /etc/ha.d/authkeys

The builtin drbddisk resource handler had some problems, so I modified
it slightly.

# nano /etc/ha.d/resource.d/drbddisk

#!/bin/bash
#
# This script is inteded to be used as resource script by heartbeat
#
# Jan 2003 by Philipp Reisner.
#
###

DEFAULTFILE="/etc/default/drbd"
DRBDADM="/sbin/drbdadm"

if [ -f $DEFAULTFILE ]; then
  . $DEFAULTFILE
fi

if [ "$#" -eq 2 ]; then
  RES="$1"
  CMD="$2"
else
  RES="all"
  CMD="$1"
fi

case "$CMD" in
    start)
        # try several times, in case heartbeat deadtime
        # was smaller than drbd ping time
        try=6
        while true; do
                $DRBDADM primary $RES && break
                let "--try" || exit 20
                sleep 1
        done
        ;;
    stop)
        # exec, so the exit code of drbdadm propagates
        exec $DRBDADM secondary $RES
        ;;
    status)
        if [ "$RES" = "all" ]; then
            echo "A resource name is required for status inquiries."
            exit 10
        fi
        ST=$( $DRBDADM state $RES 2> /dev/null )
        ST=${ST%/*}
        if [ "$ST" = "Primary" ]; then
            echo "running"
        else
            echo "stopped"
        fi
        ;;
    *)
        echo "Usage: drbddisk [resource] {start|stop|status}"
        exit 1
        ;;
esac

exit 0

Test the heartbeat resource scripts to ensure they are able to bring
up/down both the drbddisk and the xendomain.

# /etc/ha.d/resource.d/drbddisk r0 start
# /etc/ha.d/resource.d/drbddisk r0 stop
# /etc/ha.d/resource.d/xendomains xenu start
# /etc/ha.d/resource.d/xendomains/xenu stop

Bring up heartbeat on both machines

# /etc/init.d/heartbeat/start

Check status on the primary node

# cat /proc/drbd
# xm list


_______________________________________________
Xen-users mailing list
[hidden email]
http://lists.xensource.com/xen-users